Search results
A hammer drill and masonry bits. Safeguard the brick by ensuring the holes are a respectable distance from the brick's edge. The manufacturer’s compass will guide your choice of the drill bit dimension. Once you’ve finished drilling holes, it’s time to install the wall anchors and secure the mounting brackets.
- Step 1: Choose A Location
- Step 2: Find The Installation Height
- Step 3: Mark The Drill Holes
- Step 4: Drill The Holes
- Step 5: Install Plastic Anchors
- Step 6: Install The Bracket
- Step 7: Install The TV
Before you drill any holes, find a location close enough to an electrical outlet and cable jack. The fewer visible cables, the better looking the installation.
With the TV placed facedown, affix the bracket to the TV according to the bracket manufacturer’s directions. If your bracket is a two-piece, attach both pieces to the back of the TV as if they were...Measure from the bottom of the wall bracket to the bottom of the TV. You’ll add this measurement to the TV’s desired height to find the bracket mount location on the wall. If this measurement is 6...Remove the bracket from the TV. For two-piece brackets, remove just the wall bracket.Hold the wall bracket against the wall so the bracket’s bottom is at the height determined in step 2. Use a level to ensure the bracket is positioned evenly. Then, use the permanent marker to indic...If the marks end up on mortar lines, adjust the bracket to avoid the mortar and make a new mark for the drill hole. Mortar is much softer than brick, and the anchor’s grip will eventually deteriora...Keep in mind that many brackets offer several screw holes to choose from. The bracket’s instructions will explain how many and which you’ll need to use.Following the instructions on the concrete anchors or masonry screws you purchased, attach the appropriately sized masonry bit to the drill.Mark the drill bit at a length just a bit longer than the anchor or screw by wrapping a small piece of painter’s tape around the bit at that point. If you have a hammer drill, set it to the hammer...Placing the tip of the drill bit on one of the marks, squeeze the trigger slowly until the bit begins to dig into the brick. (Lightly tapping your palm on the back of the drill can also set the bit...As the bit digs into the brick, increase the drill speed. Occasionally pull the bit out slightly to remove brick dust from the hole. Continue drilling until you’ve reached the desired depth marked...Use a hammer or rubber mallet to tap the plastic anchors into the freshly drilled holes until they’re flush with the wall.Anchors don’t need a lot of force, so if they don’t install all the way, you may need to clean out more of the brick dust. Simply placing the nozzle of the running shop vac over the hole is all tha...Slide washers onto the screws if necessary. Holding the wall bracket in place (making sure it’s right side up), thread the screws through the bracket and into the drilled holes by hand.After attaching the driver bit to the drill or fitting the properly sized socket on a ratchet, tighten one screw.Check the bracket for level and then tighten the other screws until the bracket is secure.For two-piece brackets, simply install the TV brackets (already attached to the TV) on the wall bracket. Many also have locking screws or tabs that hold the TV in place—refer to your bracket instru...For one-piece brackets, have a helper hold the television in place as you thread the screws through the TV bracket and into the back of the TV.If cables are hanging below, consider placing a piece of furniture below the TV to hide the cords as much as possible.- Hang your TV at least 12 inches (30 cm) above the fireplace. Proper spacing protects your TV from heat and smoke damage. Ideally, your TV should be far enough from the fireplace to prevent the heat from affecting the screen.
- Mark the drill holes. Hold the bracket in place against the wall and mark the holes with a marker. Choose a wall mount made from high-quality materials (like stainless steel) that can support the weight of your TV.
- Drill holes into the marks. A hammer drill and masonry drill bits help cut through brick more easily. Start by gently pressing the drill trigger to get the initial holes drilled.
- Secure the TV bracket to the wall. Use your pre-drilled holes and the bracket openings as a guide. For concrete screws, use a drill to secure them into the pre-drilled holes.
The thing about mounting your TV over the fireplace is that it’s much higher than you’d naturally have wanted to put it. You can make up for the angle by putting your couch at a distance so you don’t have to crane your neck. And if your TV is big enough, you won’t mind a bit. Book TV mounting Use coupon code "TAKE10" to get 10% OFF!
Decide how high to mount the TV. Choose location for TV mount and electric. Install Electric and Wire Chase. Attach TV Mount. Mount TV to the Fireplace. 1. Identify Fireplace Structure. When you’re mounting a TV above a fireplace you need to consider the type of fireplace structure you have.
Jan 5, 2016 · Mount TV to wall mount. How To Hide Cables and Wires. Luckily, we already had an electrical outlet on a wall directly next to our fireplace (on the right, lower side of the brick fireplace). We then had a cable company install a cable receptacle on the wall directly to the left of the brick fireplace.
People also ask
How do you mount a TV to a brick fireplace?
How do you mount a TV to a wall?
How to install a TV on a brick wall?
Can you put a TV on a brick fireplace?
Can You mount a TV over a fireplace?
How do you install a TV on a fireplace?
Mar 13, 2024 · High temperatures from the fire, mounting techniques, and wire management are essential factors to consider before hanging a TV above a fireplace, so make sure your setup will be safe and practical. 1. Check the Temperature Before You Hang a TV Above a Fireplace. You may be planning to burn a fire while watching TV.
