Yahoo Canada Web Search

Search results

1. www.floortrendsmag.com › articles › 110981-50-or-3350% or 33% Offset? It’s now in the Handbook ... - Floor ...

   www.floortrendsmag.com › articles › 110981-50-or-33

   • Cached

   Jul 30, 2012 · By moving the intersection of the two ends of the tiles to the 33% location from the 50% location, the lippage is significantly reduced and most times provides an acceptable appearance. Many tile manufacturers now recommend that their products be installed with the 33% offset which further supports tile mechanic’s need to install a tile ...

2. www.tileletter.com › offset-patterns-dos-and-dontsOffset patterns dos and don'ts - TileLetter

   www.tileletter.com › offset-patterns-dos-and-donts

   • Cached

   Nov 6, 2020 · 50% offset for 12”x24” tile. ANSI A108.02 section 4.3.8.2 is where the answer is. I will paraphrase what it says – When tiles with sides longer than 15” are being set with their long sides next to each other they shall be set in a pattern with an offset of 33% or less. If an offset more than 33% is desired (such as a 50% offset), the ...

3. www.tileletter.com › why-do-manufacturers-requireWhy do manufacturers require a 33% offset brick pattern?

   www.tileletter.com › why-do-manufacturers-require

   • Cached

   May 14, 2019 · On numerous jobs, for both walls and floors, we are asked by interior designers to install 12 x 24 or similar tiles in a standard brick aka 50% offset pattern. However, for many of these, printed on the box of tile or stated on the order sheet by the distributor, it clearly states in one way or another, “Brick joint pattern to be offset 33%.”.

   • Author: Mark Heinlein

4. www.johnbridge.com › vbulletin › showthreadHow to do 33% Stagger - Ceramic Tile Advice Forums - John ...

   www.johnbridge.com › vbulletin › showthread

   • Cached

   May 3, 2017 · As far as the cross cuts, start a row with a full tile against the left or right wall and stick down that row. Then, for the second row, simply hook your tape on one of the corners of the first row tiles and start the second row corner at the 8 inch mark on the tape. Or if you think it needs to be 7 7/8, that's fine.

5. tcnatile.com › wp-content › uploadsRectangular Tiles: How to “Offset” Certain Installation ...

   tcnatile.com › wp-content › uploads

   with rectangular tiles currently in compliance with ANSI A137.1, North American tile manufacturers are in favor of mak-ing warpage requirements even more stringent. Currently, ANSI A137.1 states, “the warpage of each tile in the sample shall conform to the value listed in the appropriate table for that specific tile type.”

6. www.ceramictilefoundation.org › blog › offsets-groutOffsets, Grout Joints and Customer Expectations

   www.ceramictilefoundation.org › blog › offsets-grout

   • Cached

   Aug 13, 2019 · 4.3.8.2 Running bond/brick joint and any offset patterns: “For running bond/brick joint and any offset patterns (i.e., non-continuous grout joints) utilizing tiles (square and/or rectangular) where the side being offset is greater than 15” (nominal dimension), the offset pattern will be a maximum of 33% unless otherwise specified by the ...

7. People also ask

   Do tile mechanics need a 33% offset?

   • Many tile manufacturers now recommend that their products be installed with the 33% offset which further supports tile mechanic’s need to install a tile pattern that will be satisfactory.

   50% or 33% Offset? It’s now in the Handbook!

   www.floortrendsmag.com/articles/110981-50-or-33-offset-its-now-in-the-handbook

   See all results for this question

   What if a tile offset is more than 33%?

   • If an offset more than 33% is desired (such as a 50% offset), the specifier and owner must approve a mock-up and agree to the lippage that may result from this type of pattern being installed. The reason for this is that some tiles have what is called warpage as part of their manufacturing process. Warpage is when the tile is bowed in the middle.

   Offset patterns dos and don'ts - TileLetter

   www.tileletter.com/offset-patterns-dos-and-donts/

   See all results for this question

   What is a 50% offset tile pattern?

   • On numerous jobs, for both walls and floors, we are asked by interior designers to install 12 x 24 or similar tiles in a standard brick aka 50% offset pattern. However, for many of these, printed on the box of tile or stated on the order sheet by the distributor, it clearly states in one way or another, “Brick joint pattern to be offset 33%.”

   Why do manufacturers require a 33% offset brick pattern?

   www.tileletter.com/why-do-manufacturers-require-a-33-offset-brick-pattern/

   See all results for this question

   How much offset do you need for tile?

   • Some manufacturers will have specific offset requirements for their tiles. They may require a 20% or 25% maximum offset. So – if you would like a 50% offset, you need to ask your tile contractor to lay them out or physically install a few so you can view them as they will look in the finished installation.

   Offset patterns dos and don'ts - TileLetter

   www.tileletter.com/offset-patterns-dos-and-donts/

   See all results for this question

   Should a brick joint pattern be offset 33%?

   • However, for many of these, printed on the box of tile or stated on the order sheet by the distributor, it clearly states in one way or another, “Brick joint pattern to be offset 33%.” When we point this out, the designer doesn’t care and won’t approve a mockup (because they don’t want to order any extra tile).

   Why do manufacturers require a 33% offset brick pattern?

   www.tileletter.com/why-do-manufacturers-require-a-33-offset-brick-pattern/

   See all results for this question

   What is the maximum offset for wood look tiles?

   • Most of these wood look tiles are planks that range from 3” up to 9” wide and lengths from 24” to 72” and beyond. In other words, they are large format and will be subject to inherent warpage. That's why the ANSI Specification A108.02-4.3.8.2 recommends - as mentioned above - a maximum offset of 33%.

   Offsets, Grout Joints and Customer Expectations

   www.ceramictilefoundation.org/blog/offsets-grout-joints-customer-expectations

   See all results for this question

8. www.ceramictilefoundation.org › blog › ansiANSI Standards: A Tile Installer's Best Friend!

   www.ceramictilefoundation.org › blog › ansi

   • Cached

   Nov 1, 2022 · For running bond/brick joint patterns utilizing tiles (square or rectangular) where the side being offset is greater than 18” (nominal dimension), the running bond offset will be a maximum of 33% unless otherwise specified by the tile manufacturer. If an offset greater than 33% is specified, the specifier and the owner must approve the mock ...