Search results
Nov 6, 2020 · 50% offset for 12”x24” tile. ANSI A108.02 section 4.3.8.2 is where the answer is. I will paraphrase what it says – When tiles with sides longer than 15” are being set with their long sides next to each other they shall be set in a pattern with an offset of 33% or less. If an offset more than 33% is desired (such as a 50% offset), the ...
- Before You Begin: Finding The Right Base
- Creating A Balanced Layout
- How to Avoid Awkward Cuts
- Proper Tile Setting
- Tips For Installing Tile
- Grout: The Finishing Touch
- Directory
Tile needs a supportive, rigid base. If installed directly on a surface that flexes and swells, such as plywood, it can crack and crumble. Here’s how to think about underlayment options.
Properly laid tiles are centered in the space, with roughly equal cuts on opposing sides. Here’s how to plan a layout. 1. For a floor installation, start by creating two perpendicular reference lines that intersect at the center of the room. They should be perfectly square to each other in order to avoid crooked tiles and uneven cuts. First, mark t...
Doing a dry layout allows you to check the size of the cuts that you will have to make. If you’re going to be using less than half a tile or mosaic sheet along an edge, shift the chalk line that runs parallel to that wall by half a tile. You’ll even out the cuts along the opposing walls, and the job will look better with larger tiles along the edge...
Which adhesive should you use?
Also known as the bond coat, this is the glue that fastens the tile to the underlayment 1. Thinset (versatile and reliable):The tiling standard, thinset is sand-and-cement mortar. Although it’s not waterproof, it’s safe for use in damp areas. But it may not be appropriate everywhere: With a porous—or as tile setters say, “thirsty”—concrete-based underlayment and a hard porcelain tile, thinset may not cure properly because the moisture gets pulled into the underlayment. 2. Modified Thinset (a...
How to mix thinset
Follow these steps to ensure it holds well. 1. Mix the entire bag. Don’t try to use partial bags—it’s too difficult to get the proportions exactly right. 2. Put the water or latex additive in the bucket first. Adding the powder to the liquid helps avoid dry spots. 3. Follow the manufacturer’s directions exactly for the mixer’s rpm and how long to let the thinset slake, or rest, before using it. Otherwise the bonding strength could be compromised. 4. Once it’s mixed, don’t add more water, whic...
What is back buttering?
This technique, recommended for natural-stone tile, eliminates air bubbles to ensure a superior seal. While not every type of tile requires it, Mark often takes the extra step to make sure his tile job is rock-solid After spreading a layer of adhesive onto the underlayment with a notched trowel, use the trowel’s flat edge to apply a thin coat of adhesive to the back of a tile. Set the tile in place using firm, even pressure Check your work by pulling the tile up. At least 80 percent should be...
What is the best way to cut tile?
There are several tools you can use, but a wet saw is the most versatile and gives the cleanest cuts, Mark says. Rental units often come with dull blades, which will slow down your work and can chip the tile. Mark’s tip: Buy a new blade for the rented saw; it will cost about $50 to $100.
When to use caulk or grout
Whenever tile meets another surface—where the kitchen countertop meets the backsplash, or the edge of the tub touches the tile surround—the seam should be sealed with caulk, not grout. If you use grout, it will eventually crack and fall out as the different materials shift independently of each other. Most installers will leave this joint empty, carefully working around it, and then, once the rest of the area is grouted, fill the seam with silicone caulk as a final step. But it can be difficu...
Make mesh-backed mosaic sheets look seamless
The most common flaw with mosaic tile installations: visible lines where the sheets meet. Here are some tips for avoiding them 1. Take your time to dry-fit the sheets together to achieve perfectly even spacing. This may involve trimming away some of the mesh. 2. If the spacing is off at all, “you might need to peel off a tile here and there and lay it independently,” Mark says. 3. If the design of the tile allows, cut some sheets in half, clipping around the tiles themselves, and stagger them...
Picking the right type of grout
When deciding which grout is best for your project, consider how often it will be exposed to water, dirt, and spills. A basic grout is fine for low-traffic areas, but for rooms like the kitchen, a grout with built-in stain resistance is a better choice:
Minimizing grout lines
Grout makes a tiled surface stronger and helps keep out dirt and water, but “there’s nothing pretty about it,” says Mark. “The tighter the grout joints, the better the tile job looks,” he says. He likes to go as small as 1/32 of an inch, but that requires skill, since tiny grout joints leave little room for slight differences in size and shape from one tile to the next. You could end up with two tiles that are touching, or not get any grout in the joints at all. Novice installers who want to...
Tips for a better grout job
1. Mix the grout exactly to the manufacturer’s instructions, always using the whole bag and always starting with the water. 2. Spread it over the tile and grout lines—or just over the grout lines with large-format tiles—with a grout float recommended for the type of grout you are using. Hold the float at a 45-degree angle to the tile surface, and press the grout into the joints. 3. Allow the grout to set for the manufacturer-specified time. Cover only as much area as you can get back to befor...
Thanks to Scott Carothers, director of certification and training for the Ceramic Tile Education Foundation; ceramictilefoundation.org. Ian O’Connor, product manager at Custom Building Products; custombuildingproducts.com. Andy Acker, director of education at Schluter Systems; schluter.com.
May 14, 2019 · On numerous jobs, for both walls and floors, we are asked by interior designers to install 12 x 24 or similar tiles in a standard brick aka 50% offset pattern. However, for many of these, printed on the box of tile or stated on the order sheet by the distributor, it clearly states in one way or another, “Brick joint pattern to be offset 33%.”.
- Mark Heinlein
Feb 13, 2020 · Tile laborers charge more to lay this pattern because of the precise angles and extra material waste it creates. This pattern is usually done with narrow, skinny tiles; like a 3"x12" or a 6"x36" but could also be created using a typical 3x6 subway tile. There are also two different ways to lay herringbone - 1. Stacked Herringbone 2.
Feb 26, 2022 · A staggered floor layout is also known as an offset pattern. It’s not a difficult pattern to achieve. You simply line up the edge of the tile to the center of the tile below it. You can also offset each one by one-third of the tile to give a more interesting option. That method is often called “third-stagger.”.
A137.1, North American tile manufacturers are in favor of mak-ing warpage requirements even more stringent. Currently, ANSI A137.1 states, “the warpage of each tile in the sample shall conform to the value listed in the appropriate table for that specific tile type.” While square and rectangular tiles have
People also ask
How much offset do you need for tile?
What is a 50% offset tile pattern?
What if a tile offset is more than 33%?
What is a 1/3 offset tile pattern?
How do I start a 1/3 offset tile install?
Is offset tile a safe choice?
Nov 1, 2022 · I began the 1/3 offset install starting from left to right. This resulted in the first end cut being 4-1/2″ to start the 1/3 offset. The right end cut resulted in a 3-1/2″ cut, which equals 1/3 of the 12″x24″ tile. This is the layout I chose to go with in order to control not having any smaller cuts on the ends.
