Search results
People also ask
How to configure switch in Cisco packet tracer?
How do I add a switch to Packet Tracer?
How to configure a Cisco switch?
What are the basic switch settings?
How to configure GigabitEthernet 0/2 port on switch MLS?
How do I configure a trunk interface on a layer 3 switch?
Feb 13, 2024 · This lab will test your ability to configure basic settings such as hostname, motd banner, encrypted passwords, and terminal options on a Cisco Catalyst 2960 switch emulated in Packet Tracer 8.1.1. 1.
- Asa 5506-X DMZ Configuration
Lab instructions. 1. Configure NAT to allow LAN users to...
- Packet Tracer Labs
Download free Cisco Packet Tracer 8.2.2 labs designed by our...
- DPI With Asa 5505
Despite this default behavior, the simulated ASA 5505...
- Download
This is a bugfix release fixing several bugs on...
- Asa 5506-X DMZ Configuration
- Objectives
- Background / Scenario
- Required Resources
- Part 1: Cable The Network and Verify The Default Switch Configuration
- Part 2: Configure Basic Network Device Settings
- Part 3: Verify and Test Network Connectivity
- Part 4: Manage The Mac Address Table
- Appendix A: Initialize and Reload A Switch
Part 2: Configure Basic Network Device Settings
1. Configure basic switch settings. 2. Configure the PC IP address.
Part 3: Verify and Test Network Connectivity
1. Display device configuration. 2. Test end-to-end connectivity with ping. 3. Test remote management capabilities with Telnet.
Part 4: Manage the MAC Address Table
1. Record the MAC address of the host. 2. Determine the MAC addresses that the switch has learned. 3. List the show mac address-table command options. 4. Set up a static MAC address.
Cisco switches can be configured with a special IP address known as the switch virtual interface (SVI). The SVI, or management address, can be used for remote access to the switch to display or configure settings. If the VLAN 1 SVI is assigned an IP address, by default all ports in VLAN 1 have access to the SVI IP address. In this lab, you will bui...
1 Switch (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable)1 PC (Windows with terminal emulation program, such as Tera Term)1 Console cable to configure the Cisco IOS device via the console port1 Ethernet cable as shown in the topologyIn Part 1, you will set up the network topology and verify default switch settings. a. Connect the console cable as shown in the topology. Do not connect the PC-A Ethernet cable at this time. Note:If you are using Netlab, shut down F0/6 on S1. This has the same effect as not connecting PC-A to S1. b. Connect to the switch from PC-A using Tera Term ...
In Part 2, you will configure basic settings for the switch and PC. a. Copy the following basic configuration and paste it into S1 while in global configuration mode. b. Set the SVI IP address of the switch. This allows remote management of the switch. Before you can manage S1 remotely from PC-A, you must assign the switch an IP address. The defaul...
In Part 3, you will verify and document the switch configuration, test end-to-end connectivity between PC-A and S1, and test the switch’s remote management capability. Use the console connection on PC-A to display and verify the switch configuration. The show runcommand displays the entire running configuration, one page at a time. Use the spacebar...
In Part 4, you will determine the MAC addresses that the switch has learned, set up a static MAC address on one interface of the switch, and then remove the static MAC address from that interface. Open a command prompt on PC-A and issue the ipconfig /all command to determine and record the Layer 2 (physical) addresses of the NIC. Answers will vary....
a. Console into the switch and enter privileged EXEC mode. b. Use the show flashcommand to determine if any VLANs have been created on the switch. c. If the vlan.datfile was found in flash, then delete this file. d. You are prompted to verify the filename. If you have entered the name correctly, press Enter; otherwise, you can change the filename. ...
By following the comprehensive guide outlined in this tutorial, you can effectively set up and configure a switch in Packet Tracer, including common configurations like assigning names, creating VLANs, configuring port security, setting up trunk ports, and enabling Spanning Tree Protocol (STP).
Feb 15, 2020 · Instructions. Part 1: Configure Layer 3 Switching. In Part 1, you will configure the GigabitEthernet 0/2 port on switch MLS as a routed port and verify that you can ping another Layer 3 address. a. On MLS, configure G0/2 as a routed port and assign an IP address according to the Addressing Table. MLS(config)# interface g0/2.
- Verify the Default Switch Configuration. Step 1: Enter privileged mode. You can access all switch commands from privileged mode. However, because many of the privileged commands configure operating parameters, privileged access should be password-protected to prevent unauthorized use.
- Create a Basic Switch Configuration. Step 1: Assign a name to a switch. To configure parameters on a switch, you may be required to move between various configuration modes.
- Configure a MOTD Banner. Step 1: Configure a message of the day (MOTD) banner. The Cisco IOS command set includes a feature that allows you to configure messages that anyone logging onto the switch sees.
- Save Configuration Files to NVRAM. Step 1: Verify that the configuration is accurate using the show run command. Step 2: Save the configuration file.
Oct 15, 2024 · Learn how to configure and manage a Cisco Switch step by step with this basic switch commands and configuration guide. To explain basic switch configuration commands, I will use packet tracer network simulator software.
Jun 22, 2022 · Steps to Configure the Switch: Step 1. Open the packet tracer desktop and take a switch (PT-Switch) from the devices. Step 2: Configure the Host name of the swicth0. Click on switch0 and go to Command Line Interface. Then change the hostname to “sh” Command: switch>en. switch#conf t. switch(config)#hostname sh. sh(config)exit.
