Search results
Did you know your washing machine has a drain pump filter that needs to be cleaned? The filter protects the drain pump by catching any large objects. I owned...
- 4 min
- 143.3K
- Mike attempts
Plug the wire harness into the new pump and close the wire harness cover. Reconnect the inlet hose and the drain hose to the new pump and secure them with spring clamps. Slide the cabinet back onto the washer or stand the machine back upright. Fit the main top and console of the washer back on.
- What Is A Drain Pump?
- Where Is The Drain Pump located?
- How to Access, Remove, and Inspect The Drain Pump in A Top Load Washing Machine
- How to Install A New Drain Pump in A Top Load Washing Machine
- How to Install A New Drain Pump in A Front Load Washing Machine
The drain pump flushes wastewater out from your washing machine. This water is pumped out of the drain hose and into the drainpipe or washtub. The drain pump is activated before and during the spin cycle. On some washers, the main motor drives the pump, and the pump simply has an inlet and an outlet. In other machines, the drain pump might have a m...
You can usually find the drain pump mounted to the floor of the washer, either at the front or at the back. General Location of the Drain Pump in a Top Load Washer General Location of the Drain Pump in a Front Load Washer
Begin by unplugging your washing machine and moving it away from the wall.Check and note down which hose goes to the hot connector, and which one goes to the cold connector.Next, loosen and remove the two hoses. It is normal for some water to pour out at this point.On some washers, you may need to remove the entire washer cabinet to expose the drain pump at the bottom of the washer.Check ‘How to Access, Remove, and Inspect the Drain Pump in a Top-Load Washing Machine’ for instructions on how to remove the old drain pump.With the cover already open and the wire harness plug out of the drain pump, you will simply need to remove the old drain pump and install the new one.To do this, first, remove the bolts securing the drain pump to the bottom of the washer tub and put the old pump aside.Grab your new drive pump and secure it to the bottom of the washer tub using the bolts.Check ‘How to Access, Remove, And Inspect the Drain Pump in Front Load Washing Machine’ for instructions on how to remove the old drain pump.Some manufacturers sell the complete assembly motor and pump as one, while others offer them as two separate parts. You will need to verify which one yours is as you may need to replace either the...If the pump comes separately, remove the drain pump out of the pump body and pry off the cover on the motor, if it has one.Insert and secure the new drain pump into the pump body.Jul 7, 2021 · To Check the Drain Pump: Disconnect the washer from the power source and water supply. Remove the access panel. Locate the pump. Depending on the model, there may be two or three hoses connected to it – the drain hose, the tub-to-pump hose, and a circulating hose. Inspect the pump and pump hoses for cracks and other signs of damage.
Feb 2, 2024 · – Mark your calendar to check the drain hose and clean the pump filter every 6 months. Set an annual appointment for a professional drain cleaning to prevent more headaches. Choosing Suitable Cleaning Products for the Washing Machine Drain. Skip commercial drain cleaners, which can damage pipes long-term.
Find the Drain Filter Plug for Your Washer. Inside the washing machine front area, you should see what is clearly a drain hose or pipe with an end holding the filter. Position Your Bucket and Detach the End. Place your bucket underneath the filter in case it is full of water and carefully detach the end.
People also ask
How do you replace a washing machine pump?
Where is the drain pump on a washing machine?
How do you fix a clogged washing machine?
How do you remove a drain pump from a washing machine?
How do you replace a drain pump in a top load washer?
How does a washer drain pump work?
Check the filter. A common cause of washing machine water not draining is a blockage. The first thing to check is your washing machine's filter, which can be found at the bottom of your washing machine on the front. The filter serves to collect foreign objects and prevent them from getting stuck inside the machine or reaching the pump.
