Search results
Dec 29, 2015 · Installing crown molding in your home or on a project? With this cutting technique, you use a simple jig and the built-in 45-degree miter stops on your miter...
- 5 min
- 1.3M
- WOOD magazine
- Understanding Crown Molding
- Tools and Materials For Cutting Crown Molding
- Creating Inside Corner Crown Molding Cuts
- Mastering Outside Corner Crown Molding Cuts
- Producing Scarf Joints For Crown Molding
- Tips For Accurate Molding Cuts
- Techniques For Seamless Crown Molding Joints
- Common Crown Molding Cut Mistakes to Avoid
- Our Conclusion
Crown molding is a decorative trim installed where the wall meets the ceiling. It comes in various styles and materials, but the cutting techniques remain consistent regardless of the type you choose. Before you dive into the cutting process, familiarize yourself with the following basic principles of working with crown molding.
Before you begin cutting crown molding, gather the following tools and materials: 1. Coping saw 2. Crown molding 3. Fine-grit sandpaper (100-grit) 4. Ladder for proper access to ceiling areas 5. Measuring tape 6. Pencil 7. Power miter saw 8. Safety glasses 9. Saw stand or stable work surface 10. Work gloves
Inside corners require an approach that combines a square cut with a coped cut. This method allows for a tighter fit and accommodates slight variations in wall angles. Here’s how to create inside corner cuts: 1. Make a square cut on the first piece of molding and position it tightly in the corner. 2. Set the saw to 45 degrees and make a miter cut o...
Outside corners are some of the most visible joints in crown molding, which necessitates a precise fit. Follow these steps to create perfect outside corner cuts: 1. Set the miter saw blade to 45 degrees to the left. 2. Position the first piece of molding upside down on the saw, holding it firmly against the fence and bed. 3. Make the cut. 4. Rotate...
You would use scarf joints when you need to join two pieces of crown molding along a straight run and when you’re working with walls longer than the available molding lengths. Here’s how to create a scarf joint: 1. Place the crown molding upside down on the miter saw table, holding it at the same angle as you plan to install it. 2. Set the saw blad...
To make your crown molding cuts as precise and professional-looking as possible, keep these tips in mind: 1. Always wear safety glasses and work gloves when operating power tools. 2. Double-check measurements and angles before making cuts. 3. Make test cuts on scrap pieces of molding before cutting your final pieces. 4. Mark all cuts clearly with a...
Beyond the basic cuts, achieving seamless joints is an art that requires extra attention to detail. Here’s how to ensure impeccable joints: 1. Apply a consistent layer of paint or stain to hide any visible seams. 2. Caulk all joints and corners to fill gaps and create a polished look. 3. Frequently dry fit your pieces during the installation proces...
When cutting crown molding, try to steer clear of these common pitfalls: 1. Cutting the molding in the wrong orientation 2. Failing to account for inside and outside corners when measuring 3. Forgetting to make allowances for scarf joints in long runs 4. Neglecting to sand coped edges for a smoother fit 5. Not using a stable work surface, leading t...
Cutting crown molding may seem daunting at first, but with practice and the right techniques, it becomes a manageable DIY task. By following the methods Silva demonstrates in this video and the process we’ve outlined in this guide, you can achieve professional-looking results in your next crown molding project. Remember to take your time, measure c...
- 10 min
This Old House general contractor Tom Silva shares some tricks of the trade for cutting crown molding for miters, scarf joints, and copes. (See below for a s...
- 4 min
- 2.1M
- This Old House
- Make the First Scarf Cut. When two lengths of molding are required for a long wall, join them with an angled, overlapping scarf joint. If you’re working counterclockwise around the room, adjust the saw for a 45-degree miter cut to the left.
- Complete the Scarf Joint. Apply a thin, even layer of glue to the scarf joint on the molding that’s now nailed in place. Install the adjoining piece of crown so it creates a tight-fitting scarf joint.
- Determine Angle of Outside Corner. An outside corner can be formed by cutting two pieces of crown with opposite miters of 45 degrees each, making sure both miters are longer on the top of the crown (the part that rests on the saw table when you cut).
- Test the Angle Cuts. Turn the pieces so they are stacked precisely one on top of the other (make sure to put the piece with the pencil lines on top).
Apr 18, 2006 · With the miter rotated clockwise (CW) and the trim to the left of the blade, you get a horizontal turn, inside corner, LH cut. With the same saw setting with the trim to the right of the blade, you get a horizontal turn, outside corner, RH cut. Now move the miter counterclockwise (CCW) to the opposite side of your saw.
Feb 11, 2024 · Cut the first piece of crown molding square. Place it in the miter saw and cut with the blade set to 0 degrees. Cut the second piece at a 45º angle, cutting just as you would for an outside corner. Use a dark pencil to trace along the edge of the cut (of the second piece) along the molded front of the piece.
People also ask
How do you cut crown molding on a miter saw?
How do you cut a crown molding square?
How do you use a crown molding saw?
How do you cut a crown with a saw?
How do you cut crown molding with a coping saw?
How to cut crown molding for horizontal ceilings with a miter saw?
Oct 23, 2023 · Every time you cut a miter (whether for coping or outside corners), you’ll set the crown molding upside down against the saw’s fence. It’s easy to get confused and cut the angle backward. To avoid mishaps, hold the crown molding up to the corner and draw a slash showing the direction of the cut. Clamp the crown molding to the work surface.
