Search results
Here’s how to make those adjustments: Check that the shade is straight in the window frame. If it’s off-center, gently pull it back into alignment. Find the tension adjustment mechanism near the top of the roller. Use a screwdriver to adjust the spring tension to help the shade roll up easily or stay down better.
Do you have a roller shade that won't go up anymore? We'll show you in 5 easy steps how you can fix it.NOTE: These instructions may not apply to Bali or Levo...
- 49 sec
- 340.6K
- Blinds.com
Nov 4, 2018 · Step 1: Pull your blind all the way down and hold it at a 45-degree angle away from your window. Step 2: Gently tug on your blind and then push it up. This should re-set the motor. Step 3: If the above doesn’t work you can reach up under your blind and place your hand on the tube. Give the tube a half turn.
- Lifting and Lowering Problems
- Tensioner Problems
- Installation and Mounting Problems
- Shade Material Problems
- Need Replacement Roller Shades
- Child Safety Concerns
When my shade rolls up, it is drifting to one side and is fraying the edge of my shade material.
This problem is called “telescoping.” First, check to make sure the roller shade bracketshaven’t come loose from the mounting surface. Check that the brackets are level and even. Roller shades must be mounted absolutely level to operate correctly. If the brackets are level and tight, it could be the shade material itself causing this. To correct it, unroll the shade all the way until you can see the exposed roller tube. Put a piece of masking tape on the side opposite from the telescoping (un...
The shade material came off of the tube.
Most of the time, the shade material is attached with double-sided tape. You can oftentimes restick the material to the tape. Or, replace the tape with a new strip of double-sided tape. Sometimes the material can come off of the tube because it is “over-rolled.” That means that when you’re lowering the shade, you keep pulling on the chain and the fabric rolls completely off of the tube. This can make it difficult for the shade to roll up again properly. Installing bead chain stopsto prevent t...
When I pull on the chain to raise the shade up and down, the shade won’t move or is hard to move.
This can be a problem with the bead chain or the clutch mechanism. Inspect the bead chain to see if it is broken, fraying or has broken beads. Replace the chain if it is worn. If the chain is in good condition, the clutch may be broken or worn out and need replacement.
My control chain is blowing around and won’t stay down.
All chain loops should be tied down to the wall, floor or window frame using a tension device. If your shade is missing a tension device or yours has become broken, it’s easy to install a new one.
My chain gets hung up going through the tension device.
Some tension devices are made for chain connectors to pass through, and some are not. If your chain is getting stuck or snagged where the chain connector is located, changing the tensioner for a larger one that accommodates connectors will help. We specify if a connector is accommodated in every tension device on its product page under “Additional Information.”
Can I mount my roller shade inside or outside the window?
Most brackets can be mounted either inside or outside the window. We specify the mounting type each roller shade bracketaccommodates on its product page under “Additional Information.”
The shade mounted on my door bangs against the door when the door is opened or closed.
Installing hold down bracketswill secure the bottom of the shade to the door. You may also need to replace broken or missing bottom rail end caps that have been damaged or lost from the shade hitting the door.
I had a new window installed and now my shade is too wide for my window frame.
You will need to have your shade cut to the proper width. Most local blind repair shops can cut blinds and shades, but we recommend checking with them before taking your window covering to them. If you are the original owner, you can try contacting the company you purchased the shades from. Also, consider mounting your shade outside the window.
Several things can go wrong with the shade material. It can tear or become soiled, and cleaning won’t work. The edges of the material can fray. Whenever there is an issue with the material, it is time to replace the entire shade. We do not carry shade material at Fix My Blinds or have a referral for replacement material.
This page includes affiliate links. If you visit click the below link and make a purchase, we may received a small commision at no extra cost to you. We only recommend products we would sell. If your roller shade is beyond repair, we recommendBlinds.comfor replacements.
I’m afraid my child or pet will become tangled in the cords on my roller shades.
Please visit the Window Covering Safety Councilto see the latest recommendations for corded window coverings.
Feb 9, 2010 · This is a problem with the tension spring. You can adjust this easily. Too Slow - Start with a lowered shade. Remove the shades from the bracket. Then roll it up by hand to the half way point. When you replace them, it should work just fine. Too Fast - Start with the shade up. Remove it from the brackets.
Apr 28, 2018 · Step 7: Repeat this process until your roller shade has the correct tension to roll up all the way. Cordless Cellular Shades: Cellular shades, also known as honeycomb shades, are pleated shades made of fabric that form a “cell” shape. You can see the cell shape when you look at the shade from the side. The cords on a cellular shade run up ...
People also ask
Can a roller shade go up all the way?
Why does my Roller shade roll up?
Why are my roller blinds not rolling up?
How do I know if my roller shades are working correctly?
How do roller shades work?
Why is my shade not moving?
Dec 23, 2022 · Twist the flat pin at the roller’s end with the plier in a clockwise direction. It will release the spring from the inside. You will hear the sound of the pawl when it releases the ratchet. When it’s done, bring the shade down and roll it to half its length to adjust the spring. Now put the shade back into its brackets and check if it’s ...
